Explore The Variety Of Hot Water Heaters On The Market Today

With energy costs on the rise, tankless hot water heaters have become a popular choice for homeowners. Tankless water heaters are much more efficient then their traditional tank type water heaters. The conventional tank type water heater stores and heats energy, day in and day out. This means that while you’re at work, on vacation, or just sleeping, your tank type traditional water heater is working away, wasting hard to come by energy. It was one thing to have traditional tank type water heaters wasting energy when energy prices were low, but now that we are in a rather large energy crisis, tankless hot water heaters make more sense than ever.

Water and Energy Savings

The beauty of a tankless system is that it does not constantly waste energy when it is not needed. Tankless water heaters, or on demand water heaters, on the other hand, only use energy when you need it. So, they are inherently more efficient. Depending on your situation, you can save as much as 50 percent on your utility bills by utilizing this relatively new technology. Now, installing one of these newfangled tankless water heaters is not always going to be cheap. Some tankless water heaters, like gas tankless hot water heaters require special routing, combustion, and gas line requirements. This can make what seemed like a simple job, not only a complicated, but also an expensive one. So, it is not always an open and shut case. When it comes to new construction, going with a little bit more expensive tankless water heater unit, makes more sense than ever.

The Different Types

There are two typical types of tankless units, gas and electric. Deciding which hot water heater is most appropriate for you is dependent on your unique situation. Gas and electric tankless heaters, both come with their benefits and drawbacks. Gas tankless water heaters are the most powerful available. They are ideal for a whole home set up. They produced the flow rates necessary to supply hot water for an entire help. Electric tankless heaters, on the other hand, are better suited for single point locations. Examples would include an isolated shower location, a kitchen application, or even a remote hot tub set up. Electric tankless water heaters are also much more economical when it comes to installation; however, electrical panel changes may be required.

Because electric tankless hot water heaters can be installed right at the point of use, they are extremely energy efficient. In a perfect world, installing electric tankless water heaters at every hot water source would provide for a very green home. Do to the costs of these tankless electric water heaters, installing at several locations is just too cost prohibitive. That is why, tankless gas water heaters are the obvious choice for providing hot water for a whole home.

Which Type Is Best

Before you rush out and buy one of these hot new tankless units, it is important to do a little homework. You need to decide which tankless water heater is right for your specific household needs. Do you need hot water for your whole house? If so, a gas unit might be a good choice. Do you have hot water needs that will surpass your tankless water heaters flow rates? If that’s the case, you may need to run a series of units.

Now, if you just need more hot water at a dishwasher, washing machine, or any other point of use location, and tankless electric water heater would be the obvious choice. It is also important to check with your local utility, as they often offer incentives, through tankless tax rebates. The federal government previously offered a $300 rebate for qualifying tankless water heaters. Currently, we are patiently awaiting legislation, which would allow for continuation of this attractive offer. These incentives make what seems like an expensive appliance, a very affordable one. Combine this with the substantial energy savings, and you have a great deal.

If you decide that this type of water heating system is right for your home then we suggest you do a little research on the local plumbing companies to find a Vancouver hot water heater replacement contractor who you are comfortable with. Ask a few questions about the type you’ll need for your home, the number of people there and number of installations you’re considering. They should be able to recommend something that will fir your usage, budget and needs.

Your Forced Air Furnace Maintenance Guide

Looking for some quick tips on how to keep your gas furnace in tip-top shape this winter? This furnace tune up guide will answer all of your questions, including how to turn on a furnace, how to change a furnace filter, how to test a furnace’s airflow, what to do if a furnace doesn’t ignite, and much more.

A) How to Turn On Your Gas Furnace

It sounds easy, but believe it or not, many people don’t know how to turn their furnace on or off. Here’s a simple, step-by-step breakdown:

  • Find the breaker for your furnace. It’s part of the electrical panel, which is usually located in your basement, utility room or garage. The breaker should be clearly labeled with a gas furnace sticker. Turn the breaker to the “On” position.
  • Locate and turn on the furnace switch. It is typically somewhere near the bottom of your basement stairs – sometimes in the ceiling, sometimes in the furnace room itself, and usually at eye level or slightly higher.
  • Set your thermostat. Check that the furnace is on and then make sure that the selector switch is set to “Heat”. Finally, adjust your set point temperature, and that’s it – your furnace is turned and ready to heat your home!

B) How to Check and Change Your Furnace Filter

Proper maintenance of your furnace filter can help optimize airflow from your furnace, which will keep it running efficiently and economically during the coldest months of the year. To prevent burnout of your furnace parts, we recommend inspecting your filter monthly and changing it every three to six months. Here’s how it’s done:

  • Begin by carefully opening the furnace’s external rack or panel door.
  • Remove the furnace filter by sliding it out. Take a look at the filter to see if there’s any darkness or discoloration.
  • If you can’t see through the filter, it’s definitely time for a new one. Slide the new filter into the furnace, making sure that it is installed in the direction of the airflow. And that’s it – you’re done!

C) How to Test Your Furnace’s Airflow

If a room in your house is too cold during the winer, it might be because your furnace isn’t supplying enough warm air through the registers in that particular room. There’s a simple way to test the airflow from your furnace registers to make sure they are working properly — the garbage bag airflow test.

The test is a quick way to estimate airflow by determining how long it takes to fill a common plastic garbage bag. While it is not a precise measurement, it is better than no measurement at all and will give you a good ideas as to whether you need to call a technician to look at your ductwork.

To do the garbage bag airflow test:

  • Tape the mouth of the garbage bag to a coat hanger or piece of cardboard to keep it open.
  • Crush the bag flat and place it over the register or exhaust hood.
  • Count the number of seconds it takes for the bag to fully inflate.

If the inflation time is:

  • 2 seconds = 37 L/s (75 cfm)
  • 4 seconds = 20 L/s (40 cfm)
  • 10 seconds = 10 L/s (20 cfm)

If the measured airflow is less than 10 L/s, the furnace is delivering only a small amount of heat to a room and needs to be further inspected to determine why the heat is not going through.

The garbage bag airflow test is also useful if you have changed your heating or cooling systems or have made major renovations to your house.

D) If Your Gas Furnace Fails to Ignite

If you can hear that your furnace is on and the fan is running, but all you’re getting is cold air, you likely have ignition failure. Try resetting your furnace by turning the switch to off for at least ten seconds, then, turning it on again. If that doesn’t do the trick, give your HVAC contractor a call.

E) Furnace Troubleshooting Checklist

Think your gas furnace has quit? You could save yourself the cost of a no-heat service call by checking the following:

Is the furnace switch in the on position? It may have been turned off by mistake.

  • Is the thermostat properly set to the “heat” position and the temperature set to your normal heat setting?
  • Is the furnace venting blocked by snow or ice? If so, try to remove the blockage.
  • Are the programmable thermostat batteries fresh?
  • Is the circuit breaker in the electric panel in the proper position?
  • Is the furnace door properly closed?
  • Has the filter been changed recently? If you’ve checked everything on the list and your furnace still isn’t working, give your local HVAC contractor a call, and they’ll get your furnace back up and running as soon as possible.

F) How to Properly Remove Vent Blockages

If you become aware of a furnace problem that might involve the exterior vent, do a quick inspection and see if any snow, ice or some common household item might be blocking the vent. If so, before removing the obstruction, head inside first and turn the off the power to your furnace. Now, you can safely clear away whatever is blocking your exterior vent. Once you’re done, turn your furnace back on using either the breaker or the switch.

A lack of airflow through the furnace’s interior vents could mean your furnace fan motor has seized. If this has happened, don’t try to fix the problem yourself – contact the expert furnace repair technicians at your local HVAC contractor.

G) How to Stop Air Leaks and Prevent Heat Loss

Air leaks account for a significant amount of a home’s heat loss in winter – resulting in increased heating costs as your furnace constantly tries to replace the warm air that has escaped from your home. Fixing these leaks will save you money on your heating bills.

To stop leaks around windows and doors:

  • Remove the trims carefully.
  • Fill large cracks or gaps with foam backer rod, oakum, or expanding polyurethane foam.
  • Replace the trims and caulk along the edges.

To stop leaks along baseboards:

  • Caulk along the seams without removing the baseboard.
  • Remove the baseboard and caulk between the wall and the floor.

To stop leaks around electrical outlets on outside walls:

  • Turn off power to the outlet and remove the outlet cover.\Install a foam insulating pad.
  • Replace the outlet cover turn the power back on to the outlet.

To stop leaks in an unfinished basement:

  • Caulk under the basement sill plate and around the joists with a rubber-based caulking or acoustical sealant.
  • Caulk any gaps where ducts enter a wall or ceiling.
  • Insulate ducts with preformed wraps or duct-taped insulation batts.

To stop leaks in your attic:

  • Seal any cracks.
  • Weather strip your attic door and close it tightly.

H) If a Gas Smell is Detected

In the unlikely event that you smell something like a rotten egg smell, you could have a gas leak. Don’t turn on any electrical switches and open all of your windows. Then, go to a neighbor’s house and contact your HVAC contractor or your local gas provider immediately.

If you find all of this a little overwhelming then you can do what thousands of other homeowners do which is call a local plumber. You can easily find a reputable furnace tune up Vancouver contractor by doing a little research on the reviews you find online.

Get Familiar With The Water Pressure In Your Home

Plumbing is the kind of thing most people would rather sweep under the rug. Unfortunately, too many of us tend to forget about the plumbing in our homes and as a result simple problems become costly issues. Save yourself hours of frustration and an expensive plumbing bill by taking the time to get familiar with pipes and valves in your home.

Know Your Water Pressure Limits

The Uniform Plumbing Code (UPC) calls for water to be delivered to homes for domestic use at between 50 to 70 psi. Angle stops (valves) and supply lines as well as appliances are designed to withstand up to 80 pounds per square inch.

Water pressure regulators take the water as it is delivered by the water district, and regulate it to between 50 and 70 psi. The pieces in the water pressure regulator that reduce the water pressure are made of rubber and metal. Over a period of time, they fail. When the water pressure regulator fails, water pressure to the home is allowed to increase. This puts a strain on valves, hoses and appliances that they were not designed to withstand. Unchecked, excessive water pressure may cause a rupture in the supply lines or valves.

A water pressure test gauge can inform the homeowner if water pressure is excessive. Simply connect the gauge to an outdoor faucet, and turn on the water to determine the water pressure. Make sure the faucet used is “regulated”. Some outdoor faucets are unregulated. If the pipe connected to the faucet comes out of the wall, there is a fairly good chance that faucet is regulated.

Generally speaking, replacing the water pressure regulator, including parts and labor, should cost much less than a homeowner’s standard $500 deductible. A working water pressure regulator reduces the strain on plumbing fixtures and increases their service life. If the worst happens and you do have a burst pipe then here are a few tips to help with the clean-up.


Cleaning Up After a Leak

1. Turn off water to the house.
2. Remove as much water as possible with mopping and blotting.

3. Remove all photos, art and small fixtures to a safe, dry place.

4. Remove damp books from shelves and spread out to dry.

5. Wipe wooden furniture dry. Prop up cushions for even drying.

6. Open drawers, cabinets and closets for faster drying.

7. Put aluminum foil, saucers or wood blocks between furniture legs and wet carpeting.

8. Remove rugs from on top of wet carpet to prevent color saturation.

9. Remove items that are not colorfast, such as books and magazines, from wet flooring and carpet.

10. Immediately use fans to circulate air and encourage drying.

11. Try to stabilize the indoor air temperature to about 70 degrees and use dehumidifiers, if possible.

The best advice we can offer is to call a local professional for plumbing services and have them test the pressure while its on your mind. In most cases everything is okay, but if something does need to be replaced then it’s bets to do it before something awful happens.

Sometimes a leaking faucet can be caused by high water pressure. If something starts leaking all of a sudden, then you might want to have it checked out.

3 Ways To Deal With Kitchen Remodeling Stress

Without even leaving your home you’ll find the doors that you need in hand within a few days. The small space has an electrical box and a large sink. Pulling on the heartstrings is the key to winning over the Number 2 personality.

You might have been hearing the word refacing for quite some time already and yet your mind keeps on telling you that new furniture is a better catch than the latter. Well, open your senses and broaden your mind because Reface kitchen cabinets cincinnati Cabinets wonders is about to reveal its biggest mystery to you.

If you would like to save some money fixing up your bathroom you can paint the light switches. Don’t kitchen gadget catalogs to do the plug-in covers as well. There are several easy home improvement projects that you can do to the bathroom. Maybe you could add a toilet seat cover and matching towels to add a nice look. The cost is very minimal, but can add a nice touch to the room. If you have a spare bedroom you may want to consider painting those switches as well.

Considering that outdoor kitchens australia can be a bit costly, it is important to opt doing them yourself in a bid to save. The first step is finding softwares that are going to help you map out the whole kitchen before you embark on the practice. The next step is ensuring that you get all the required tools before commencing the project to facilitate a smooth sailing. Proceed to carry out the renovations, though first starting with the exterior part of the kitchen making your way to the inside. If there are any fixtures that you need, you can have them performed now. For instance if you had made plans on lighting under the cabinets, you could proceed with the wiring and leave it at that waiting for the next time.

You could develop terrific appearances merely by going with a more affordable alternative. For instance if your kitchen closets are dated, rather than replacing them, transform or painting just the doorways; another great idea is to merely replace the deals with. This isn’t going to set you back a lot to do yet will certainly achieve some really outstanding outcomes. Staying on this topic, the very same concept puts on your flooring. If you are hoping for tiled flooring you could wind up investing the whole allocate the room on this, which is why you could wish to consider lino that is in the pattern of stated ceramic tiles.

House paint – The house paint is to be used on large areas on the body of the house. If you look for a house paint that has a medium to high gloss, choose an oil-based one. On the other hand, if you want a house paint that is flatter and duller, buy the latex type.

When you choose your appliances for your outdoor kitchen, just remember you do not have to buy everything at once. If you just must have that top of the line grill, then wait a little while before you buy it, everything does not need to be purchased when the project begins. You can choose your grill based on your preference. Do you love that wonderful smoky taste? Buy a charcoal grill. They come in many varieties and styles, you are sure to find one that suits your unique personality. Do you love the convince and quickness of a gas grill? Then that is what you need. There are even certain models that can be used as both. What ever suits you.

If you can use a regular brush and “cut in” or trim ceilings and edges of cabinet tops (places where cabinets meet ceilings), you might not need a trim brush. I used one, though to help paint our kitchen cabinets.

Practice increasing awareness of “who you are,” core values, what you absolutely want, and what’s actually happening day-to-day. Make time for quiet solitude to invite your inner voice out to play- journaling, walking– anything that helps you to tune in.

There are many carpenters offering their services in any given town or city, but to find a good carpenter among the lot is not that easy. But when you finally found one, keep his contact details. You will never know when you will need his services again.

Not only can this option be pricey, but it can also take quite awhile to complete. Replacement kitchen doors can be the exact solution you are looking for. You need great design ideas and ways to organize your outdoor kitchen. Maple is a hardwood and therefore it will last longer than other softer woods. But, there’s now this little thing called the internet. We primed our doors with a product called BIN, a special primer.